Most GE dryer repairs in Galveston involve the same few systems: heat, airflow, the drum drive and the controls. Below are independent repair companies serving Galveston, with those that mention GE first, then the nearest dryer repair companies.
This is an independent directory. We are not affiliated with GE, and the technicians listed are independent repair companies, not the manufacturer.
GE Dryer Repair Near Galveston
Our data shows 22 appliance repair companies inside a 30-mile radius of Galveston. 2 list an address in Galveston, and the rest are spread across League City (6), Friendswood (3), and La Marque (2). Distances run up to about 30 miles. Of those, 1 mentions GE by name. M & M Appliances is the nearest, roughly 5.4 miles from Galveston. Rated companies nearby average 4.5 stars across 21 businesses.
Listings come from public business data. A brand or service mention means the company names it in its listing or website; it is not a certification. Verify experience, licensing and insurance before hiring.
| Three nearest companies, miles away | 5.4, 6.9, 9.5 |
|---|---|
| With 4.5+ stars and at least 10 reviews | 8 |
| Repair companies inside 30 miles | 22 |
| List dryer or washer & dryer work | 7 |
| Mention GE | 1 |
| Open on Saturdays (per listing) | 16 |
The leading options for Galveston are Sears Appliance Repair (23.6 miles away, based in Alvin, 4.4 stars from 84 reviews, lists Saturday hours); Sears Appliance Repair (57.5 miles away, based in Liberty, 4.7 stars from 126 reviews, lists Saturday hours); Mr. Appliance of League City (27.5 miles away, based in Friendswood, 4.8 stars from 765 reviews, lists Saturday hours); Appliance Force (22.9 miles away, based in League City, 4.9 stars from 75 reviews).
GE Dryer Lines and Features
How GE Dryers Are Built
Sensor dry models must sit level so tumbling clothes contact the moisture sensors; an unlevel dryer can end cycles with clothes still damp. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
GE Dryer Symptoms and First Checks
- Dryer will not run or start. GE's first check is that the dryer plug is pushed fully into the wall outlet. Source: GE Appliances - Dryer - Will Not Run or Start
- Dryer hot to the touch or sweating. GE says this usually means heat and humidity cannot escape, so clean the exhaust duct, clear the wall cap and confirm the elbow count suits the vent length. Source: GE Appliances - Dryer - Hot to the Touch or Sweats
GE Dryer Error Codes
| Code | What it means |
|---|---|
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
GE Dryer Problems Worth a Service Call
- Dryer shuts off a few minutes into the cycle
- Burning or hot smell during a cycle
- Drum turns but the air stays cool
How a Dryer Service Call Usually Goes in Galveston
Keeping a GE Dryer Running
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
- Clean the lint filter before every load and periodically wash it in warm soapy water to remove fabric softener film. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
Brand guides: GE Dryer Not Heating: What to Check.
GE Dryer Repair Cost Ranges
Most GE dryer repairs involve common parts and an hour or so of labor. For reference, published cost guides report:
- Control board (part only): $90–$280 Source: Angi - How Much Does Dryer Repair Cost?
- Door switch replacement: $50–$150 Source: Fixr - How much does it cost to repair a dryer?
- Drum belt replacement: $150–$250 Source: Fixr - How much does it cost to repair a dryer?
- Gas valve coil replacement (gas dryer): $150–$300 Source: Fixr - How much does it cost to repair a dryer?
- Typical dryer repair (most homeowners): $100–$430 Source: Angi - How Much Does Dryer Repair Cost?
- Service call fee (may be waived if the technician does the repair): $50–$80 per visit Source: Angi - How Much Does It Cost to Repair a Dryer?
Replacement makes more sense once a dryer is about 10 years old or past half its expected lifespan. Source: Fixr - How much does it cost to repair a dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
What to Have Ready for a GE Dryer Call
- Whether the dryer is gas or electric
- What happens when you press Start (no response, hum, runs with no heat, stops early)
- How long the vent run is and where it exits the house
Local Notes for Galveston
Most dryer calls in Galveston come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Texas has no separate appliance repair license; under the Plumbing License Law, appliance dealers and their employees may install and service appliances (other than water heaters) without a plumbing license when hooking up to existing openings with a code-approved appliance connector, while other gas or water piping work generally requires a plumbing license. Source: Plumbing License Law, Tex. Occ. Code ch. 1301, §1301.053 (Texas State Board of Plumbing Examiners)
Gas piping counts as plumbing in Texas and requires a plumbing license, with an exemption for LP gas installers who hold a separate state LP gas license. Source: Plumbing License Law, Tex. Occ. Code ch. 1301, §§1301.002, 1301.055 (Texas State Board of Plumbing Examiners)
Before You Book in Galveston
- Can you give a written estimate before ordering parts?
- Is your company licensed where my state requires it, and insured?
- If a part has to be ordered, how soon can you come back to finish?
GE Dryer Repair FAQs: Galveston, TX
Is this GE customer service?
Should I repair or replace my GE dryer?
What makes a dryer stop heating?
Related Repair Pages for Galveston
More GE Dryer Repair Pages Nearby
Before you call, find the model and serial number on your GE dryer's label, usually inside the door opening. A technician who knows the model can often tell you on the phone what the first visit will involve.