If your GE dryer has stopped heating, stopped tumbling or started throwing an error code, the technician you call should know the model line. Below are independent repair companies serving Texas City, with those that mention GE first, then the nearest dryer repair companies.
This is an independent directory. We are not affiliated with GE, and the technicians listed are independent repair companies, not the manufacturer.
GE Dryer Repair Near Texas City
We found 40 appliance repair companies within 30 miles of Texas City. The rest are spread across Pasadena (12), League City (6), and Friendswood (3). Tim Schlageter AA Apliance is the nearest, roughly 2.6 miles from Texas City. 1 lists GE specifically. The 39 rated companies in range average 4.4 stars.
Companies are shown by relevance and distance from Texas City. A mention does not mean manufacturer certification, so ask each company about its experience with your dryer.
| Distance to the three closest (mi) | 2.6, 3.0, 6.0 |
|---|---|
| Show laundry appliance work | 20 |
| With 4.5+ stars and at least 10 reviews | 22 |
| Open on Saturdays (per listing) | 45 |
| Repair companies inside 30 miles | 59 |
| Mention GE | 1 |
Closest matches for Texas City: Sears Appliance Repair (16.6 miles away, based in Alvin, 4.4 stars from 84 reviews, lists Saturday hours); Sears Appliance Repair (47.1 miles away, based in Liberty, 4.7 stars from 126 reviews, lists Saturday hours); Mr. Appliance of League City (16.3 miles away, based in Friendswood, 4.8 stars from 765 reviews, lists Saturday hours); Appliance Force (10.8 miles away, based in League City, 4.9 stars from 75 reviews).
GE Dryer Lines and Features
What a GE Dryer Technician Deals With
An electric GE dryer receiving only partial (120V) power from its 240V circuit can tumble normally but produce no heat, and a dryer wired to a 120V circuit can take up to three times longer to dry. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
Sensor dry models must sit level so tumbling clothes contact the moisture sensors; an unlevel dryer can end cycles with clothes still damp. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
What GE Says to Check First
- Dryer hot to the touch or sweating. GE says this usually means heat and humidity cannot escape, so clean the exhaust duct, clear the wall cap and confirm the elbow count suits the vent length. Source: GE Appliances - Dryer - Hot to the Touch or Sweats
- Dryer will not run or start. GE's first check is that the dryer plug is pushed fully into the wall outlet. Source: GE Appliances - Dryer - Will Not Run or Start
Reading a GE Dryer Error Code
| Code | What it means |
|---|---|
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
Signs Your GE Dryer Needs a Technician
- Clothes still damp after a full cycle
- Drum will not turn even though you hear a hum
- Outside of the cabinet gets unusually hot
Inside a Dryer Repair Visit
Care GE Recommends for Its Dryers
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
- Clean the lint filter before every load and periodically wash it in warm soapy water to remove fabric softener film. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
Brand guides: GE Dryer Not Heating: What to Check.
What GE Dryer Repairs Cost
Most GE dryer repairs involve common parts and an hour or so of labor. For reference, published cost guides report:
- Thermostat replacement: $100–$260 Source: Fixr - How much does it cost to repair a dryer?
- Door switch replacement: $50–$150 Source: Fixr - How much does it cost to repair a dryer?
- Igniter replacement (gas dryer): $100–$250 Source: Fixr - How much does it cost to repair a dryer?
- Typical dryer repair (most homeowners): $100–$430 Source: Angi - How Much Does Dryer Repair Cost?
- Technician service / diagnostic fee, dryer: $50–$80 per visit Source: Fixr - How much does it cost to repair a dryer?
A dryer that keeps needing repairs despite regular maintenance is usually cheaper to replace. Source: Angi - How Much Does Dryer Repair Cost?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
What to Have Ready for a GE Dryer Call
- Any error code on the display
- Whether the dryer is gas or electric
- How long the vent run is and where it exits the house
Local Notes for Texas City
Most dryer calls in Texas City come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Texas has no separate appliance repair license; under the Plumbing License Law, appliance dealers and their employees may install and service appliances (other than water heaters) without a plumbing license when hooking up to existing openings with a code-approved appliance connector, while other gas or water piping work generally requires a plumbing license. Source: Plumbing License Law, Tex. Occ. Code ch. 1301, ยง1301.053 (Texas State Board of Plumbing Examiners)
In Texas, you can check a license with the Texas plumbing Public License Search or report a problem to the Texas Attorney General, Consumer Protection Division.
Questions to Ask a Texas City Technician
- What guarantee do you give on parts and labor?
- Will you check the vent and lint path as part of the visit?
- Is your company licensed where my state requires it, and insured?
GE Dryer Repair FAQs: Texas City, TX
Which Texas City technicians work on GE?
Why is my dryer running but not heating?
Is this GE customer service?
More Laundry Repair in Texas City, TX
GE Dryer Repair Near Texas City
Before you call, find the model and serial number on your GE dryer's label, usually inside the door opening. A technician who knows the model can often tell you on the phone what the first visit will involve.