A GE dryer shares most of its parts with other dryers, but its controls, error codes and sensor-dry cycles are specific to the brand. The Hurst list starts with companies that name GE, followed by other appliance repair companies that list dryer work.
This is an independent directory. We are not affiliated with GE, and the technicians listed are independent repair companies, not the manufacturer.
Independent GE Dryer Technicians, Hurst TX
Our data shows 40 appliance repair companies inside a 30-mile radius of Hurst. 6 list an address in Hurst, and other nearby bases include Fort Worth (8), Arlington (6), and Haltom City (3). The farthest listed company is about 8 miles out. Appliance Recovery is the nearest, roughly 0.2 miles from Hurst. None of the repair companies near Hurst name GE in their listings, so we show the closest appliance repair companies. Ask each one about your model before booking. The 32 rated companies in range average 4.6 stars.
Listings come from public business data. A brand or service mention means the company names it in its listing or website; it is not a certification. Verify experience, licensing and insurance before hiring.
| Distance to the three closest (mi) | 0.2, 0.6, 0.8 |
|---|---|
| Rated 4.5 stars or higher (10+ reviews) | 24 |
| Show laundry appliance work | 18 |
| Open on Saturdays (per listing) | 41 |
| Companies within 30 miles | 60 |
| Mention GE | 0 |
The leading options for Hurst are Ace Refrigeration and Appliance Repair (6.3 miles away, based in Keller, 4.9 stars from 1,857 reviews); Guinco Service Appliance Repair (3.0 miles away, based in Richland Hills, 4.7 stars from 2,159 reviews); ProStar Appliance LLC (6.1 miles away, based in Euless, 4.8 stars from 214 reviews, lists Saturday hours); Synergy Appliance (2.0 miles away, based in North Richland Hills, 4.5 stars from 145 reviews).
Know Your GE Dryer
What a GE Dryer Technician Deals With
The GE Profile UltraFast Combo uses a two-stage filter system (a mesh lint filter plus a second mesh or foam filter) located between the display and the dispenser drawers. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
Common GE Dryer Problems
- Electric dryer runs but does not heat. GE says to confirm the dryer has a dedicated 240V supply, reset the breaker fully off and on, and then inspect the power cord and terminal block for burned or loose connections. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
- Dryer hot to the touch or sweating. GE says this usually means heat and humidity cannot escape, so clean the exhaust duct, clear the wall cap and confirm the elbow count suits the vent length. Source: GE Appliances - Dryer - Hot to the Touch or Sweats
GE Dryer Error Codes
| Code | What it means |
|---|---|
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
GE Dryer Problems Worth a Service Call
- Dryer will not start when you press Start
- Outside of the cabinet gets unusually hot
- Burning or hot smell during a cycle
How a Dryer Service Call Usually Goes in Hurst
Owner Care for GE Dryers
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
- Clean the lint filter before every load and periodically wash it in warm soapy water to remove fabric softener film. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
Brand guides: GE Dryer Not Heating: What to Check.
GE Dryer Repair Cost Ranges
A GE dryer repair usually costs about the same as any other brand for the same part. Published ranges:
- Drum bearing replacement: $100–$250 Source: Fixr - How much does it cost to repair a dryer?
- Drive motor replacement: $250–$450 Source: Fixr - How much does it cost to repair a dryer?
- Door switch replacement: $50–$150 Source: Fixr - How much does it cost to repair a dryer?
- Gas valve coil replacement (gas dryer): $150–$300 Source: Fixr - How much does it cost to repair a dryer?
- Typical dryer repair: $100–$200 Source: Fixr - How much does it cost to repair a dryer?
- Appliance technician diagnosis, washer (usually waived if hired for the repair): $50–$100 per visit Source: Fixr - How much does it cost to repair a washing machine?
If a repair would cost more than about half the price of a new dryer, replacing is usually the better choice. Source: Angi - How Much Does It Cost to Repair a Dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Getting Ready for the Repair
- Any error code on the display
- What happens when you press Start (no response, hum, runs with no heat, stops early)
- How long the vent run is and where it exits the house
Around Hurst
Most dryer calls in Hurst come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Texas has no separate appliance repair license; under the Plumbing License Law, appliance dealers and their employees may install and service appliances (other than water heaters) without a plumbing license when hooking up to existing openings with a code-approved appliance connector, while other gas or water piping work generally requires a plumbing license. Source: Plumbing License Law, Tex. Occ. Code ch. 1301, ยง1301.053 (Texas State Board of Plumbing Examiners)
In Texas, you can check a license with the Texas plumbing Public License Search or report a problem to the Texas Attorney General, Consumer Protection Division.
Before You Book in Hurst
- Can you give a written estimate before ordering parts?
- If a part has to be ordered, how soon can you come back to finish?
- What guarantee do you give on parts and labor?
GE Dryer Repair FAQs: Hurst, TX
Why does my dryer take so long to dry?
What should I do about a GE error code?
How do I find a technician who knows GE dryers?
Related Repair Pages for Hurst
GE Dryer Repair Near Hurst
Before you call, find the model and serial number on your GE dryer's label, usually inside the door opening. A technician who knows the model can often tell you on the phone what the first visit will involve.