Most GE dryer repairs in Benton involve the same few systems: heat, airflow, the drum drive and the controls. The Benton list starts with companies that name GE, followed by other appliance repair companies that list dryer work.
Washer and Dryer Repair is independent and not affiliated with GE. Listed companies are independent technicians who repair GE dryers and other brands.
GE Dryer Repair Near Benton
Our data shows 40 appliance repair companies inside a 30-mile radius of Benton. 2 list an address in Benton, and other nearby bases include Little Rock (22), North Little Rock (11), and Maumelle (3). Nearest on the list: Sears Appliance Repair, around 0.5 miles out. None of the companies within 30 miles mention GE by name, so we include matching companies from a longer drive plus the nearest appliance repair companies. Across 14 rated companies, the average public rating is 4.0 stars.
Companies are shown by relevance and distance from Benton. A mention does not mean manufacturer certification, so ask each company about its experience with your dryer.
| With 4.5+ stars and at least 10 reviews | 6 |
|---|---|
| Mention GE | 0 |
| Repair companies inside 30 miles | 58 |
| Three nearest companies, miles away | 0.5, 0.9, 10.7 |
| List dryer or washer & dryer work | 8 |
| Listing Saturday hours | 47 |
First up for Benton: Sears Appliance Repair (85.6 miles away, based in Hope, 4.7 stars from 51 reviews, lists Saturday hours); Sears Appliance Repair (0.5 miles away, 4.4 stars from 299 reviews, lists Saturday hours); A-Tech Appliance Service (20.4 miles away, based in Little Rock, 4.6 stars from 187 reviews); Central One Service (15.9 miles away, based in Little Rock, 4.7 stars from 1,997 reviews, lists Saturday hours).
Know Your GE Dryer
What a GE Dryer Technician Deals With
Sensor dry models must sit level so tumbling clothes contact the moisture sensors; an unlevel dryer can end cycles with clothes still damp. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
Common GE Dryer Problems
- Check Vent alert. GE says to unplug the dryer, disconnect and vacuum the duct, and make sure the outside hood damper moves freely. Source: GE Appliances - Dryer - Check Vent Sensor Alert
- Electric dryer runs but does not heat. GE says to confirm the dryer has a dedicated 240V supply, reset the breaker fully off and on, and then inspect the power cord and terminal block for burned or loose connections. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
Reading a GE Dryer Error Code
| Code | What it means |
|---|---|
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
GE Dryer Problems Worth a Service Call
- Clothes still damp after a full cycle
- Drum will not turn even though you hear a hum
- Burning or hot smell during a cycle
What Gets Fixed on a Benton Dryer Call
Owner Care for GE Dryers
- Clean the lint filter before every load and periodically wash it in warm soapy water to remove fabric softener film. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
Brand guides: GE Dryer Not Heating: What to Check.
What GE Dryer Repairs Cost
Most GE dryer repairs involve common parts and an hour or so of labor. For reference, published cost guides report:
- Heating element replacement: $150–$350 Source: Fixr - How much does it cost to repair a dryer?
- Gas valve coil replacement (gas dryer): $150–$300 Source: Fixr - How much does it cost to repair a dryer?
- Drive motor replacement: $250–$450 Source: Fixr - How much does it cost to repair a dryer?
- Control board (part only): $90–$280 Source: Angi - How Much Does Dryer Repair Cost?
- Technician labor: $50–$100 per hour Source: Angi - How Much Does Dryer Repair Cost?
Replacement makes more sense once a dryer is about 10 years old or past half its expected lifespan. Source: Fixr - How much does it cost to repair a dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
What to Have Ready for a GE Dryer Call
- How long the vent run is and where it exits the house
- The brand, model and serial number from the label inside the door or on the back panel
- What happens when you press Start (no response, hum, runs with no heat, stops early)
What Benton Owners Should Know
Most dryer calls in Benton come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Arkansas has no separate appliance repair license, and household appliances are listed as exempt equipment under the state HVACR licensing law, though exempt work must still meet HVACR rules and any local permit and inspection requirements. Source: Arkansas HVAC/R Statutes 2025, A.C.A. ยง 17-33-102 (Arkansas Department of Labor and Licensing)
Natural gas piping and equipment work is governed by the state plumbing and fuel gas codes, and gas fitters are licensed by the Arkansas Department of Health's Plumbing and Natural Gas program. Source: Plumbing & Natural Gas - Arkansas Department of Health
Before You Book in Benton
- How often do you repair GE dryers, and do you carry common parts on the truck?
- What is the service call or diagnostic fee, and is it applied to the repair?
- Can you give a written estimate before ordering parts?
GE Dryer Repair FAQs: Benton, AR
Is this GE customer service?
Why do my clothes come out damp?
What should I do about a GE error code?
Is my GE dryer worth repairing?
Other Dryer Repair in Benton
More GE Dryer Repair Pages Nearby
Clean the lint screen, check the vent hood outside and note the model number before calling. It rules out the simple causes and speeds up a GE repair.