If your GE dryer has stopped heating, stopped tumbling or started throwing an error code, the technician you call should know the model line. Below are independent repair companies serving Ashton-Sandy Spring, with those that mention GE first, then the nearest dryer repair companies.
Independent listings only: Washer and Dryer Repair is not affiliated with or endorsed by GE. If your dryer is still under manufacturer coverage, contact GE directly.
GE Dryer Repair Near Ashton-Sandy Spring
We found 40 appliance repair companies within 30 miles of Ashton-Sandy Spring. The rest are spread across Silver Spring (8), Rockville (7), and Gaithersburg (5). Distances run up to about 9 miles. Nearest on the list: Ashton Affordable Appliance Repair Tech, around 0.4 miles out. No company within 30 miles of Ashton-Sandy Spring names GE in its listing, so the list adds matches from farther out and the closest appliance repair companies. Across 35 rated companies, the average public rating is 4.7 stars.
We do not show business phone numbers. Call our helpline to be connected with a participating technician, or look a company up directly. Always confirm licensing and insurance.
| Mention GE | 0 |
|---|---|
| Three nearest companies, miles away | 0.4, 1.0, 2.9 |
| Companies within 30 miles | 60 |
| Listing Saturday hours | 41 |
| Rated 4.5 stars or higher (10+ reviews) | 14 |
| Show laundry appliance work | 8 |
First up for Ashton-Sandy Spring: District-Columbia Hotpoint Rpr (17.6 miles away, based in Washington, 5.0 stars from 4 reviews, lists Saturday hours); Trusted Home Experts (8.9 miles away, based in Rockville, 4.9 stars from 289 reviews, lists Saturday hours); Mr. Appliance of Montgomery County, MD (8.4 miles away, based in Gaithersburg, 4.7 stars from 122 reviews, lists Saturday hours); Dexterous Appliance Repair (4.2 miles away, based in Fulton, 4.9 stars from 319 reviews).
Know Your GE Dryer
How GE Dryers Are Built
Sensor dry models must sit level so tumbling clothes contact the moisture sensors; an unlevel dryer can end cycles with clothes still damp. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
Common GE Dryer Problems
- Dryer hot to the touch or sweating. GE says this usually means heat and humidity cannot escape, so clean the exhaust duct, clear the wall cap and confirm the elbow count suits the vent length. Source: GE Appliances - Dryer - Hot to the Touch or Sweats
- Check Vent alert. GE says to unplug the dryer, disconnect and vacuum the duct, and make sure the outside hood damper moves freely. Source: GE Appliances - Dryer - Check Vent Sensor Alert
GE Dryer Error Codes
| Code | What it means |
|---|---|
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
Signs Your GE Dryer Needs a Technician
- Burning or hot smell during a cycle
- Dryer shuts off a few minutes into the cycle
- Outside of the cabinet gets unusually hot
What a Dryer Repair Technician Checks
Owner Care for GE Dryers
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
- Clean the lint filter before every load and periodically wash it in warm soapy water to remove fabric softener film. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
Brand guides: GE Dryer Not Heating: What to Check.
Budgeting for a GE Dryer Repair
Most GE dryer repairs involve common parts and an hour or so of labor. For reference, published cost guides report:
- Drum bearing replacement: $100–$250 Source: Fixr - How much does it cost to repair a dryer?
- Drive motor replacement: $250–$450 Source: Fixr - How much does it cost to repair a dryer?
- Control board (part only): $90–$280 Source: Angi - How Much Does Dryer Repair Cost?
- Typical dryer repair: $100–$200 Source: Fixr - How much does it cost to repair a dryer?
- Technician service / diagnostic fee, dryer: $50–$80 per visit Source: Fixr - How much does it cost to repair a dryer?
Replacement makes more sense once a dryer is about 10 years old or past half its expected lifespan. Source: Fixr - How much does it cost to repair a dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
What to Have Ready for a GE Dryer Call
- How long the vent run is and where it exits the house
- What happens when you press Start (no response, hum, runs with no heat, stops early)
- Whether the dryer is gas or electric
Local Notes for Ashton-Sandy Spring
Most dryer calls in Ashton-Sandy Spring come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Maryland does not issue a separate appliance repair license; the Maryland Board of Plumbing licenses plumbers, natural gas fitters and propane gas fitters, whose trades cover gas connections. Source: License Requirements - Maryland Board of Plumbing (Maryland Department of Labor)
The Maryland Board of Plumbing issues master, journey and apprentice natural gas fitter licenses and a propane gas fitter certificate, and recognizes certain Baltimore County and WSSC gas fitter licenses. Source: Md. Code, Business Occupations and Professions § 12-302 (Maryland General Assembly)
Hiring a Dryer Repair Company in Ashton-Sandy Spring
- Can you look at the washer on the same visit if it is acting up too?
- Can you give a written estimate before ordering parts?
- Will you check the vent and lint path as part of the visit?
GE Dryer Repair FAQs: Ashton-Sandy Spring, MD
Why is my dryer running but not heating?
Why does my GE dryer show an error code?
Should I repair or replace my GE dryer?
Related Repair Pages for Ashton-Sandy Spring
GE Dryer Repair Near Ashton-Sandy Spring
Write down any error code your GE dryer shows and when it appears. It helps a Ashton-Sandy Spring technician bring the right parts.