If your GE dryer has stopped heating, stopped tumbling or started throwing an error code, the technician you call should know the model line. Below are independent repair companies serving Fairmont, with those that mention GE first, then the nearest dryer repair companies.
Washer and Dryer Repair is independent and not affiliated with GE. Listed companies are independent technicians who repair GE dryers and other brands.
Independent GE Dryer Technicians, Fairmont MN
Our data shows 21 appliance repair companies inside a 60-mile radius of Fairmont. 1 list an address in Fairmont, and the rest are spread across Mankato (5), New Ulm (3), and Algona (2). Distances run up to about 56 miles. None of the repair companies near Fairmont name GE in their listings, so we show the closest appliance repair companies. Ask each one about your model before booking. Sears Appliance Repair is the nearest, roughly 0.8 miles from Fairmont. The 19 rated companies in range average 4.4 stars. Because the nearest shops are farther out, ask each company whether Fairmont is inside its regular service area.
Listings come from public business data. A brand or service mention means the company names it in its listing or website; it is not a certification. Verify experience, licensing and insurance before hiring.
| Open on Saturdays (per listing) | 12 |
|---|---|
| Mention GE | 0 |
| List dryer or washer & dryer work | 4 |
| Companies within 60 miles | 21 |
| Three nearest companies, miles away | 0.8, 25.2, 34.3 |
| Rated 4.5 stars or higher (10+ reviews) | 9 |
First up for Fairmont: Sears Appliance Repair (0.8 miles away, 4.7 stars from 6 reviews, lists Saturday hours); Sears Appliance Repair (45.1 miles away, based in New Ulm, 4.7 stars from 41 reviews, lists Saturday hours); Sears Appliance Repair (40.5 miles away, based in Algona, 4.4 stars from 15 reviews, lists Saturday hours); Don's Appliance & TV of Minnesota (54.2 miles away, based in St Peter, 3.8 stars from 67 reviews, lists Saturday hours).
Know Your GE Dryer
What a GE Dryer Technician Deals With
The GE Profile UltraFast Combo uses a two-stage filter system (a mesh lint filter plus a second mesh or foam filter) located between the display and the dispenser drawers. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
An electric GE dryer receiving only partial (120V) power from its 240V circuit can tumble normally but produce no heat, and a dryer wired to a 120V circuit can take up to three times longer to dry. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
Common GE Dryer Problems
- Check Vent alert. GE says to unplug the dryer, disconnect and vacuum the duct, and make sure the outside hood damper moves freely. Source: GE Appliances - Dryer - Check Vent Sensor Alert
- Dryer will not run or start. GE's first check is that the dryer plug is pushed fully into the wall outlet. Source: GE Appliances - Dryer - Will Not Run or Start
GE Dryer Error Codes
| Code | What it means |
|---|---|
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
When to Call for GE Dryer Repair
- Outside of the cabinet gets unusually hot
- Drum turns but the air stays cool
- Clothes still damp after a full cycle
What a Dryer Repair Technician Checks
Care GE Recommends for Its Dryers
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
- Inspect and clean the exhaust duct at least once a year by unplugging the dryer, disconnecting the duct and vacuuming it, and check that the outside hood flaps move freely with no nests inside. Source: GE Appliances - Dryer - How to Clean Exhaust / Vent Duct
Brand guides: GE Dryer Not Heating: What to Check.
Budgeting for a GE Dryer Repair
Most GE dryer repairs involve common parts and an hour or so of labor. For reference, published cost guides report:
- Drum roller replacement: $100–$150 Source: Fixr - How much does it cost to repair a dryer?
- Igniter replacement (gas dryer): $100–$250 Source: Fixr - How much does it cost to repair a dryer?
- Drive motor replacement: $250–$450 Source: Fixr - How much does it cost to repair a dryer?
- Technician labor: $50–$100 per hour Source: Angi - How Much Does Dryer Repair Cost?
If a repair would cost more than about half the price of a new dryer, replacing is usually the better choice. Source: Angi - How Much Does It Cost to Repair a Dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
What to Have Ready for a GE Dryer Call
- Whether the dryer is gas or electric
- How long the vent run is and where it exits the house
- Any error code on the display
Local Notes for Fairmont
Most dryer calls in Fairmont come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Minnesota has no state license for mechanical contractors or their workers; businesses contracting for gas, heating, cooling or refrigeration work file a mechanical contractor bond with the Department of Labor and Industry, and some cities require their own licenses or competency cards. Source: DLI: Mechanical contractor bond requirements
The state does not license gas fitters; contractors doing gas work must be bonded with the Department of Labor and Industry, and cities such as Minneapolis and St. Paul set their own gas fitter licensing. Source: DLI: Mechanical contractor bond requirements
Before You Book in Fairmont
- Can you give a written estimate before ordering parts?
- What is the service call or diagnostic fee, and is it applied to the repair?
- What guarantee do you give on parts and labor?
GE Dryer Repair FAQs: Fairmont, MN
Why do my clothes come out damp?
Which Fairmont technicians work on GE?
What makes a dryer stop heating?
Related Repair Pages for Fairmont
More GE Dryer Repair Pages Nearby
Clean the lint screen, check the vent hood outside and note the model number before calling. It rules out the simple causes and speeds up a GE repair.