If your GE dryer has stopped heating, stopped tumbling or started throwing an error code, the technician you call should know the model line. The Laconia list starts with companies that name GE, followed by other appliance repair companies that list dryer work.
Independent listings only: Washer and Dryer Repair is not affiliated with or endorsed by GE. If your dryer is still under manufacturer coverage, contact GE directly.
GE Dryer Repair Near Laconia
We found 13 appliance repair companies within 30 miles of Laconia. Other nearby bases include Concord (4), Belmont (2), and Bristol (2). The farthest listed company is about 26 miles out. None of the companies within 30 miles mention GE by name, so we include matching companies from a longer drive plus the nearest appliance repair companies. Baron's Major Brands Appliances - Belmont is the nearest, roughly 4.6 miles from Laconia. The 12 rated companies in range average 4.3 stars.
We do not show business phone numbers. Call our helpline to be connected with a participating technician, or look a company up directly. Always confirm licensing and insurance.
| Mention GE | 0 |
|---|---|
| Rated 4.5 stars or higher (10+ reviews) | 7 |
| Listing Saturday hours | 8 |
| Three nearest companies, miles away | 4.6, 8.9, 9.1 |
| Appliance repair companies in range (30 mi) | 13 |
| List dryer or washer & dryer work | 6 |
First up for Laconia: Sears Appliance Repair (59.4 miles away, based in Newburyport, 4.6 stars from 321 reviews, lists Saturday hours); Baron's Major Brands Appliances - Belmont (4.6 miles away, based in Belmont, 4.8 stars from 685 reviews, lists Saturday hours); Baron's Major Brands Appliances- Concord (23.7 miles away, based in Concord, 4.8 stars from 1,619 reviews, lists Saturday hours); Sears Appliance Repair (24.1 miles away, based in Concord, 4.6 stars from 280 reviews, lists Saturday hours).
GE Dryer Lines and Features
How GE Dryers Are Built
An electric GE dryer receiving only partial (120V) power from its 240V circuit can tumble normally but produce no heat, and a dryer wired to a 120V circuit can take up to three times longer to dry. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
The GE Profile UltraFast Combo uses a two-stage filter system (a mesh lint filter plus a second mesh or foam filter) located between the display and the dispenser drawers. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
What GE Says to Check First
- Dryer takes too long to dry. GE points first to venting (metal duct, no kinks, clear wall cap) and a clean lint filter, then to load size, dryer level and washer spin speed. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
- Gas dryer runs but does not heat. GE says to confirm a real drying cycle and temperature are selected, keep the front of the dryer unblocked, check the dedicated 120V outlet, and on new installs make sure the gas line is turned on. Source: GE Appliances - Gas Dryer - Runs But Does Not Heat
What GE Dryer Codes Mean
| Code | What it means |
|---|---|
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
When to Call for GE Dryer Repair
- Clothes still damp after a full cycle
- Squealing, thumping or grinding while it runs
- Dryer will not start when you press Start
How a Dryer Service Call Usually Goes in Laconia
Care GE Recommends for Its Dryers
- Clean the lint filter before every load and periodically wash it in warm soapy water to remove fabric softener film. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
Brand guides: GE Dryer Not Heating: What to Check.
Budgeting for a GE Dryer Repair
Most GE dryer repairs involve common parts and an hour or so of labor. For reference, published cost guides report:
- Door switch replacement: $50–$150 Source: Fixr - How much does it cost to repair a dryer?
- Timer replacement: $150–$300 Source: Fixr - How much does it cost to repair a dryer?
- Drum bearing replacement: $100–$250 Source: Fixr - How much does it cost to repair a dryer?
- Heating element replacement: $150–$350 Source: Fixr - How much does it cost to repair a dryer?
- Technician labor: $50–$100 per hour Source: Angi - How Much Does Dryer Repair Cost?
If a repair would cost more than about half the price of a new dryer, replacing is usually the better choice. Source: Angi - How Much Does It Cost to Repair a Dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
What to Have Ready for a GE Dryer Call
- Any error code on the display
- How long the vent run is and where it exits the house
- The brand, model and serial number from the label inside the door or on the back panel
Around Laconia
Most dryer calls in Laconia come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
New Hampshire has no license for appliance repair as such; fuel gas work, including gas appliance installation and service, is licensed by the Mechanical Safety and Licensing Board, whose licenses are limited to their named specialty. Source: N.H. RSA 153:29 (NH General Court)
Fuel gas fitters are licensed by the state Mechanical Safety and Licensing Board, with specialty licenses that include fuel gas installation technician, service technician and piping installer. Source: N.H. RSA 153:29 (NH General Court)
Before You Book in Laconia
- If a part has to be ordered, how soon can you come back to finish?
- Will you check the vent and lint path as part of the visit?
- What guarantee do you give on parts and labor?
GE Dryer Repair FAQs: Laconia, NH
Do you work for GE?
Which Laconia technicians work on GE?
What should I do about a GE error code?
Related Repair Pages for Laconia
More GE Dryer Repair Pages Nearby
Write down any error code your GE dryer shows and when it appears. It helps a Laconia technician bring the right parts.