If your GE dryer has stopped heating, stopped tumbling or started throwing an error code, the technician you call should know the model line. The Enid list starts with companies that name GE, followed by other appliance repair companies that list dryer work.
Independent listings only: Washer and Dryer Repair is not affiliated with or endorsed by GE. If your dryer is still under manufacturer coverage, contact GE directly.
GE Dryer Repair Near Enid
Our data shows 17 appliance repair companies inside a 60-mile radius of Enid. 5 of them are based in Enid itself, and the rest are spread across Stillwater (4), Edmond (3), and Waukomis (1). The farthest listed company is about 60 miles out. Nearest on the list: Arnold's Repair & Handyman Services., around 0.7 miles out. No company within 90 miles of Enid mentions GE by name, so these are the nearest appliance repair companies. Most work on several brands, so ask about yours. Across 16 rated companies, the average public rating is 4.1 stars. Enid is a smaller market, so expect a longer drive and ask whether a trip charge applies.
We do not show business phone numbers. Call our helpline to be connected with a participating technician, or look a company up directly. Always confirm licensing and insurance.
| Appliance repair companies in range (60 mi) | 17 |
|---|---|
| Mention GE | 0 |
| Three nearest companies, miles away | 0.7, 0.9, 1.3 |
| Rated 4.5 stars or higher (10+ reviews) | 7 |
| Open on Saturdays (per listing) | 11 |
| Show laundry appliance work | 4 |
Closest matches for Enid: Vacuum Center (1.3 miles away, 4.9 stars from 37 reviews, lists Saturday hours); Sears Appliance Repair (49.6 miles away, based in Stillwater, 4.7 stars from 154 reviews, lists Saturday hours); All Pro Appliance Repair Service (56.0 miles away, based in Edmond, 4.9 stars from 1,254 reviews); Alliance Appliance Repair (49.9 miles away, based in Stillwater, 4.9 stars from 323 reviews, lists Saturday hours).
GE Dryer Lines and Features
How GE Dryers Are Built
An electric GE dryer receiving only partial (120V) power from its 240V circuit can tumble normally but produce no heat, and a dryer wired to a 120V circuit can take up to three times longer to dry. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
What GE Says to Check First
- Dryer will not run or start. GE's first check is that the dryer plug is pushed fully into the wall outlet. Source: GE Appliances - Dryer - Will Not Run or Start
- Dryer hot to the touch or sweating. GE says this usually means heat and humidity cannot escape, so clean the exhaust duct, clear the wall cap and confirm the elbow count suits the vent length. Source: GE Appliances - Dryer - Hot to the Touch or Sweats
What GE Dryer Codes Mean
| Code | What it means |
|---|---|
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
When to Call for GE Dryer Repair
- Dryer will not start when you press Start
- Squealing, thumping or grinding while it runs
- Cycles take two or three runs to finish
What Gets Fixed on a Enid Dryer Call
Owner Care for GE Dryers
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
Brand guides: GE Dryer Not Heating: What to Check.
What GE Dryer Repairs Cost
Price the repair before replacing a GE dryer. Published ranges for common jobs:
- Thermostat replacement: $100–$260 Source: Fixr - How much does it cost to repair a dryer?
- Igniter replacement (gas dryer): $100–$250 Source: Fixr - How much does it cost to repair a dryer?
- Heating element replacement: $150–$350 Source: Fixr - How much does it cost to repair a dryer?
- Dryer not heating (repair by symptom): $80–$420 Source: Angi - How Much Does Dryer Repair Cost?
- Service call fee (may be waived if the technician does the repair): $50–$80 per visit Source: Angi - How Much Does It Cost to Repair a Dryer?
Replacement makes more sense once a dryer is about 10 years old or past half its expected lifespan. Source: Fixr - How much does it cost to repair a dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Before the Technician Arrives
- Whether the dryer is gas or electric
- The brand, model and serial number from the label inside the door or on the back panel
- Any error code on the display
Around Enid
Most dryer calls in Enid come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Oklahoma has no general appliance repair license; mechanical licensing through the Construction Industries Board excludes minor repairs the manufacturer allows an owner or agent to make, but that exclusion does not reach gas piping, gas controls, appliance venting or opening a sealed refrigeration system. Source: OAC 158:50 Mechanical Industry Rules (Oklahoma Construction Industries Board)
Natural gas piping work requires a Natural Gas Piping mechanical license or a plumbing license issued by the Oklahoma Construction Industries Board. Source: OAC 158:50 Mechanical Industry Rules (Oklahoma Construction Industries Board)
Hiring a Dryer Repair Company in Enid
- What guarantee do you give on parts and labor?
- Can you give a written estimate before ordering parts?
- Can you look at the washer on the same visit if it is acting up too?
GE Dryer Repair FAQs: Enid, OK
What makes a dryer stop heating?
Is my GE dryer worth repairing?
Which Enid technicians work on GE?
Other Dryer Repair in Enid
GE Dryer Repair Near Enid
Clean the lint screen, check the vent hood outside and note the model number before calling. It rules out the simple causes and speeds up a GE repair.