Most GE dryer repairs in Ponca City involve the same few systems: heat, airflow, the drum drive and the controls. Below are independent repair companies serving Ponca City, with those that mention GE first, then the nearest dryer repair companies.
Washer and Dryer Repair is independent and not affiliated with GE. Listed companies are independent technicians who repair GE dryers and other brands.
GE Dryer Repair Near Ponca City
Our data shows 18 appliance repair companies inside a 60-mile radius of Ponca City. 1 list an address in Ponca City, and the rest are spread across Enid (5), Stillwater (4), and Arkansas City (1). Davis Furniture & Appliance is the nearest, roughly 1.6 miles from Ponca City. No company within 90 miles of Ponca City mentions GE by name, so these are the nearest appliance repair companies. Most work on several brands, so ask about yours. The 17 rated companies in range average 4.2 stars. Ponca City is a smaller market, so expect a longer drive and ask whether a trip charge applies.
We do not show business phone numbers. Call our helpline to be connected with a participating technician, or look a company up directly. Always confirm licensing and insurance.
| Open on Saturdays (per listing) | 10 |
|---|---|
| Show laundry appliance work | 4 |
| Distance to the three closest (mi) | 1.6, 25.5, 32.6 |
| Repair companies inside 60 miles | 18 |
| Mention GE | 0 |
| Rated 4.5 stars or higher (10+ reviews) | 7 |
At the top of the Ponca City list: Affordable Appliance Solutions (35.9 miles away, based in Winfield, 4.9 stars from 40 reviews); Sears Appliance Repair (42.3 miles away, based in Stillwater, 4.7 stars from 154 reviews, lists Saturday hours); Alliance Appliance Repair (43.2 miles away, based in Stillwater, 4.9 stars from 323 reviews, lists Saturday hours); Sears Appliance Repair (41.6 miles away, based in Wellington, 4.6 stars from 277 reviews, lists Saturday hours).
GE Dryer Features Technicians Work On
What Makes GE Dryer Repairs Different
GE allows only rigid or flexible metal vent duct and says plastic flexible duct is not acceptable because it collapses, cuts airflow and can collect water. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
The GE Profile UltraFast Combo uses a two-stage filter system (a mesh lint filter plus a second mesh or foam filter) located between the display and the dispenser drawers. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
What GE Says to Check First
- Dryer hot to the touch or sweating. GE says this usually means heat and humidity cannot escape, so clean the exhaust duct, clear the wall cap and confirm the elbow count suits the vent length. Source: GE Appliances - Dryer - Hot to the Touch or Sweats
- Dryer takes too long to dry. GE points first to venting (metal duct, no kinks, clear wall cap) and a clean lint filter, then to load size, dryer level and washer spin speed. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
Reading a GE Dryer Error Code
| Code | What it means |
|---|---|
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
When to Call for GE Dryer Repair
- Drum will not turn even though you hear a hum
- Burning or hot smell during a cycle
- Cycles take two or three runs to finish
What Gets Fixed on a Ponca City Dryer Call
Care GE Recommends for Its Dryers
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
Brand guides: GE Dryer Not Heating: What to Check.
GE Dryer Repair Cost Ranges
A GE dryer repair usually costs about the same as any other brand for the same part. Published ranges:
- Igniter replacement (gas dryer): $100–$250 Source: Fixr - How much does it cost to repair a dryer?
- Heating element replacement: $150–$350 Source: Fixr - How much does it cost to repair a dryer?
- Drum roller replacement: $100–$150 Source: Fixr - How much does it cost to repair a dryer?
- Timer replacement: $150–$300 Source: Fixr - How much does it cost to repair a dryer?
- Technician labor: $50–$100 per hour Source: Angi - How Much Does Dryer Repair Cost?
Replacement makes more sense once a dryer is about 10 years old or past half its expected lifespan. Source: Fixr - How much does it cost to repair a dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Before the Technician Arrives
- What happens when you press Start (no response, hum, runs with no heat, stops early)
- How long the vent run is and where it exits the house
- Any error code on the display
What Ponca City Owners Should Know
Most dryer calls in Ponca City come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Oklahoma has no general appliance repair license; mechanical licensing through the Construction Industries Board excludes minor repairs the manufacturer allows an owner or agent to make, but that exclusion does not reach gas piping, gas controls, appliance venting or opening a sealed refrigeration system. Source: OAC 158:50 Mechanical Industry Rules (Oklahoma Construction Industries Board)
Natural gas piping work requires a Natural Gas Piping mechanical license or a plumbing license issued by the Oklahoma Construction Industries Board. Source: OAC 158:50 Mechanical Industry Rules (Oklahoma Construction Industries Board)
Before You Book in Ponca City
- How often do you repair GE dryers, and do you carry common parts on the truck?
- Can you give a written estimate before ordering parts?
- What guarantee do you give on parts and labor?
GE Dryer Repair FAQs: Ponca City, OK
Is this GE customer service?
Should I repair or replace my GE dryer?
Which Ponca City technicians work on GE?
Why does my GE dryer show an error code?
Related Repair Pages for Ponca City
More GE Dryer Repair Pages Nearby
Before you call, find the model and serial number on your GE dryer's label, usually inside the door opening. A technician who knows the model can often tell you on the phone what the first visit will involve.