A GE dryer shares most of its parts with other dryers, but its controls, error codes and sensor-dry cycles are specific to the brand. Below are independent repair companies serving Albany, with those that mention GE first, then the nearest dryer repair companies.
Independent listings only: Washer and Dryer Repair is not affiliated with or endorsed by GE. If your dryer is still under manufacturer coverage, contact GE directly.
Independent GE Dryer Technicians, Albany OR
Our data shows 13 appliance repair companies inside a 30-mile radius of Albany. 2 of them are based in Albany itself, and other nearby bases include Salem (7), Corvallis (2), and Independence (1). Distances run up to about 23 miles. Xigent Appliance Repair, Inc. is the nearest, roughly 1.1 miles from Albany. No company within 90 miles of Albany mentions GE by name, so these are the nearest appliance repair companies. Most work on several brands, so ask about yours. The 12 rated companies in range average 4.6 stars.
We do not show business phone numbers. Call our helpline to be connected with a participating technician, or look a company up directly. Always confirm licensing and insurance.
| Mention GE | 0 |
|---|---|
| List dryer or washer & dryer work | 2 |
| Companies within 30 miles | 13 |
| Rated 4.5 stars or higher (10+ reviews) | 7 |
| Listing Saturday hours | 5 |
| Three nearest companies, miles away | 1.1, 2.1, 8.2 |
At the top of the Albany list: Xigent Appliance Repair, Inc. (1.1 miles away, 4.8 stars from 1,237 reviews); Sears Appliance Repair (8.2 miles away, based in Corvallis, 4.5 stars from 131 reviews, lists Saturday hours); Sears Appliance Repair (22.4 miles away, based in Salem, 4.3 stars from 140 reviews, lists Saturday hours); Mike's Appliance Repair (2.1 miles away, 4.4 stars from 69 reviews).
Know Your GE Dryer
How GE Dryers Are Built
Some GE dryers have an airflow sensor that shows a Check Vent alert when exhaust airflow drops, which usually means the vent is blocked. Source: GE Appliances - Dryer - Check Vent Sensor Alert
GE Dryer Symptoms and First Checks
- Electric dryer runs but does not heat. GE says to confirm the dryer has a dedicated 240V supply, reset the breaker fully off and on, and then inspect the power cord and terminal block for burned or loose connections. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
- Check Vent alert. GE says to unplug the dryer, disconnect and vacuum the duct, and make sure the outside hood damper moves freely. Source: GE Appliances - Dryer - Check Vent Sensor Alert
What GE Dryer Codes Mean
| Code | What it means |
|---|---|
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
GE Dryer Problems Worth a Service Call
- Dryer shuts off a few minutes into the cycle
- Outside of the cabinet gets unusually hot
- Burning or hot smell during a cycle
What a Dryer Repair Technician Checks
Care GE Recommends for Its Dryers
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
Brand guides: GE Dryer Not Heating: What to Check.
Budgeting for a GE Dryer Repair
Most GE dryer repairs involve common parts and an hour or so of labor. For reference, published cost guides report:
- Thermal fuse repair: $80–$130 Source: Angi - How Much Does It Cost to Repair a Dryer?
- Door switch replacement: $50–$150 Source: Fixr - How much does it cost to repair a dryer?
- Drum roller replacement: $100–$150 Source: Fixr - How much does it cost to repair a dryer?
- Drive motor replacement: $250–$450 Source: Fixr - How much does it cost to repair a dryer?
- Typical dryer repair (most homeowners): $100–$430 Source: Angi - How Much Does Dryer Repair Cost?
- Service call fee (may be waived if the technician does the repair): $50–$80 per visit Source: Angi - How Much Does It Cost to Repair a Dryer?
Replacement makes more sense once a dryer is about 10 years old or past half its expected lifespan. Source: Fixr - How much does it cost to repair a dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
What to Have Ready for a GE Dryer Call
- The brand, model and serial number from the label inside the door or on the back panel
- What happens when you press Start (no response, hum, runs with no heat, stops early)
- How long the vent run is and where it exits the house
Around Albany
Most dryer calls in Albany come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Oregon has no license issued specifically for appliance repair that we could confirm, but anyone installing or servicing liquefied petroleum (LP) gas appliances needs an LP gas fitter license from the Oregon State Fire Marshal. Source: Liquefied Petroleum Gas licensing (Oregon State Fire Marshal)
In Oregon, you can check a license with the Oregon Construction Contractors Board Contractor/License Search or report a problem to the Oregon Department of Justice, Consumer Protection.
Before You Book in Albany
- Can you give a written estimate before ordering parts?
- Is your company licensed where my state requires it, and insured?
- Will you check the vent and lint path as part of the visit?
GE Dryer Repair FAQs: Albany, OR
Is my GE dryer worth repairing?
Why do my clothes come out damp?
Which Albany technicians work on GE?
Is this GE customer service?
Related Repair Pages for Albany
More GE Dryer Repair Pages Nearby
Before you call, find the model and serial number on your GE dryer's label, usually inside the door opening. A technician who knows the model can often tell you on the phone what the first visit will involve.