A GE dryer shares most of its parts with other dryers, but its controls, error codes and sensor-dry cycles are specific to the brand. Below are independent repair companies serving Henderson, with those that mention GE first, then the nearest dryer repair companies.
Washer and Dryer Repair is independent and not affiliated with GE. Listed companies are independent technicians who repair GE dryers and other brands.
GE Dryer Repair Near Henderson
Within 30 miles of Henderson there are 23 appliance repair companies in our data. Other nearby bases include Jackson (22) and Lexington (1). The farthest listed company is about 21 miles out. None of the companies within 30 miles mention GE by name, so we include matching companies from a longer drive plus the nearest appliance repair companies. The closest is Pledge Appliance Repair Technicians, about 11.6 miles away. Across 23 rated companies, the average public rating is 4.8 stars.
Listings come from public business data. A brand or service mention means the company names it in its listing or website; it is not a certification. Verify experience, licensing and insurance before hiring.
| List dryer or washer & dryer work | 2 |
|---|---|
| Rated 4.5 stars or higher (10+ reviews) | 3 |
| Distance to the three closest (mi) | 11.6, 12.5, 14.2 |
| Repair companies inside 30 miles | 23 |
| Open on Saturdays (per listing) | 8 |
| Mention GE | 0 |
First up for Henderson: Sears Appliance Repair (32.4 miles away, based in Milan, 1.0 stars from 2 reviews, lists Saturday hours); Sears Appliance Repair (78.1 miles away, based in Blytheville, 4.4 stars from 25 reviews, lists Saturday hours); Sears Appliance Repair (17.7 miles away, based in Jackson, 4.5 stars from 187 reviews, lists Saturday hours); Meals Appliance Repair (19.9 miles away, based in Lexington, 4.6 stars from 49 reviews).
GE Dryer Lines and Features
How GE Dryers Are Built
An electric GE dryer receiving only partial (120V) power from its 240V circuit can tumble normally but produce no heat, and a dryer wired to a 120V circuit can take up to three times longer to dry. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
Sensor dry models must sit level so tumbling clothes contact the moisture sensors; an unlevel dryer can end cycles with clothes still damp. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
Common GE Dryer Problems
- Dryer takes too long to dry. GE points first to venting (metal duct, no kinks, clear wall cap) and a clean lint filter, then to load size, dryer level and washer spin speed. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
- Electric dryer runs but does not heat. GE says to confirm the dryer has a dedicated 240V supply, reset the breaker fully off and on, and then inspect the power cord and terminal block for burned or loose connections. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
What GE Dryer Codes Mean
| Code | What it means |
|---|---|
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
When to Call for GE Dryer Repair
- Outside of the cabinet gets unusually hot
- Drum turns but the air stays cool
- Clothes still damp after a full cycle
What a Dryer Repair Technician Checks
Owner Care for GE Dryers
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
- Clean the lint filter before every load and periodically wash it in warm soapy water to remove fabric softener film. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
Brand guides: GE Dryer Not Heating: What to Check.
GE Dryer Repair Cost Ranges
Most GE dryer repairs involve common parts and an hour or so of labor. For reference, published cost guides report:
- Control board (part only): $90–$280 Source: Angi - How Much Does Dryer Repair Cost?
- Timer replacement: $150–$300 Source: Fixr - How much does it cost to repair a dryer?
- Drum bearing replacement: $100–$250 Source: Fixr - How much does it cost to repair a dryer?
- Typical dryer repair: $100–$200 Source: Fixr - How much does it cost to repair a dryer?
- Appliance technician diagnosis, washer (usually waived if hired for the repair): $50–$100 per visit Source: Fixr - How much does it cost to repair a washing machine?
If a repair would cost more than about half the price of a new dryer, replacing is usually the better choice. Source: Angi - How Much Does It Cost to Repair a Dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
What to Have Ready for a GE Dryer Call
- Any error code on the display
- The brand, model and serial number from the label inside the door or on the back panel
- How long the vent run is and where it exits the house
Around Henderson
Most dryer calls in Henderson come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Tennessee's Board for Licensing Contractors does not list an appliance repair license among the licenses it issues (general contractor, home improvement, limited licensed electrician and limited licensed plumber). Source: TN Board for Licensing Contractors
Gas piping and gas appliance installation permits are handled by local governments, some of which require their own gas fitter license; for example, Chattanooga requires a city Master Gas Fitter License to pull a gas permit. Source: City of Chattanooga: Gas Permit
Questions to Ask a Henderson Technician
- Can you look at the washer on the same visit if it is acting up too?
- What is the service call or diagnostic fee, and is it applied to the repair?
- Will you check the vent and lint path as part of the visit?
GE Dryer Repair FAQs: Henderson, TN
Why does my GE dryer show an error code?
Is my GE dryer worth repairing?
What makes a dryer stop heating?
Is this GE customer service?
Related Repair Pages for Henderson
GE Dryer Repair in Nearby Cities
Before you call, find the model and serial number on your GE dryer's label, usually inside the door opening. A technician who knows the model can often tell you on the phone what the first visit will involve.