GE owners in Lexington usually want two things from a repair company: experience with the brand and quick access to parts. Below are independent repair companies serving Lexington, with those that mention GE first, then the nearest dryer repair companies.
This is an independent directory. We are not affiliated with GE, and the technicians listed are independent repair companies, not the manufacturer.
Who Works on GE Dryers Near Lexington
Our data shows 26 appliance repair companies inside a 30-mile radius of Lexington. 1 list an address in Lexington, and the rest are spread across Jackson (22), Huntingdon (1), and Milan (1). Distances run up to about 29 miles. Meals Appliance Repair is the nearest, roughly 1.7 miles from Lexington. 1 lists GE specifically. Across 26 rated companies, the average public rating is 4.6 stars.
Companies are shown by relevance and distance from Lexington. A mention does not mean manufacturer certification, so ask each company about its experience with your dryer.
| Mention GE | 1 |
|---|---|
| List dryer or washer & dryer work | 4 |
| Repair companies inside 30 miles | 26 |
| Rated 4.5 stars or higher (10+ reviews) | 5 |
| Distance to the three closest (mi) | 1.7, 21.5, 21.5 |
| Open on Saturdays (per listing) | 10 |
Closest matches for Lexington: Sears Appliance Repair (26.2 miles away, based in Milan, 1.0 stars from 2 reviews, lists Saturday hours); Sears Appliance Repair (86.9 miles away, based in Blytheville, 4.4 stars from 25 reviews, lists Saturday hours); Sears Appliance Repair (24.5 miles away, based in Jackson, 4.5 stars from 187 reviews, lists Saturday hours); Meals Appliance Repair (1.7 miles away, 4.6 stars from 49 reviews).
GE Dryer Features Technicians Work On
What Makes GE Dryer Repairs Different
An electric GE dryer receiving only partial (120V) power from its 240V circuit can tumble normally but produce no heat, and a dryer wired to a 120V circuit can take up to three times longer to dry. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
GE allows only rigid or flexible metal vent duct and says plastic flexible duct is not acceptable because it collapses, cuts airflow and can collect water. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
What GE Says to Check First
- Dryer hot to the touch or sweating. GE says this usually means heat and humidity cannot escape, so clean the exhaust duct, clear the wall cap and confirm the elbow count suits the vent length. Source: GE Appliances - Dryer - Hot to the Touch or Sweats
- Electric dryer runs but does not heat. GE says to confirm the dryer has a dedicated 240V supply, reset the breaker fully off and on, and then inspect the power cord and terminal block for burned or loose connections. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
Reading a GE Dryer Error Code
| Code | What it means |
|---|---|
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
Signs Your GE Dryer Needs a Technician
- Cycles take two or three runs to finish
- Squealing, thumping or grinding while it runs
- Dryer shuts off a few minutes into the cycle
What a Dryer Repair Technician Checks
Care GE Recommends for Its Dryers
- Inspect and clean the exhaust duct at least once a year by unplugging the dryer, disconnecting the duct and vacuuming it, and check that the outside hood flaps move freely with no nests inside. Source: GE Appliances - Dryer - How to Clean Exhaust / Vent Duct
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
Brand guides: GE Dryer Not Heating: What to Check.
Budgeting for a GE Dryer Repair
A GE dryer repair usually costs about the same as any other brand for the same part. Published ranges:
- Door switch replacement: $50–$150 Source: Fixr - How much does it cost to repair a dryer?
- Thermostat replacement: $100–$260 Source: Fixr - How much does it cost to repair a dryer?
- Gas valve coil replacement (gas dryer): $150–$300 Source: Fixr - How much does it cost to repair a dryer?
- Typical dryer repair (most homeowners): $100–$430 Source: Angi - How Much Does Dryer Repair Cost?
- Technician labor: $50–$100 per hour Source: Angi - How Much Does Dryer Repair Cost?
If a repair would cost more than about half the price of a new dryer, replacing is usually the better choice. Source: Angi - How Much Does It Cost to Repair a Dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
What to Have Ready for a GE Dryer Call
- Whether the dryer is gas or electric
- Any error code on the display
- The brand, model and serial number from the label inside the door or on the back panel
What Lexington Owners Should Know
Most dryer calls in Lexington come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Tennessee's Board for Licensing Contractors does not list an appliance repair license among the licenses it issues (general contractor, home improvement, limited licensed electrician and limited licensed plumber). Source: TN Board for Licensing Contractors
Gas piping and gas appliance installation permits are handled by local governments, some of which require their own gas fitter license; for example, Chattanooga requires a city Master Gas Fitter License to pull a gas permit. Source: City of Chattanooga: Gas Permit
How to Choose a Dryer Technician Near Lexington
- Is your company licensed where my state requires it, and insured?
- Can you look at the washer on the same visit if it is acting up too?
- How often do you repair GE dryers, and do you carry common parts on the truck?
GE Dryer Repair FAQs: Lexington, TN
Why do my clothes come out damp?
What should I do about a GE error code?
What makes a dryer stop heating?
Related Repair Pages for Lexington
More GE Dryer Repair Pages Nearby
Clean the lint screen, check the vent hood outside and note the model number before calling. It rules out the simple causes and speeds up a GE repair.