If your GE dryer has stopped heating, stopped tumbling or started throwing an error code, the technician you call should know the model line. Below are independent repair companies serving Brigham City, with those that mention GE first, then the nearest dryer repair companies.
Washer and Dryer Repair is independent and not affiliated with GE. Listed companies are independent technicians who repair GE dryers and other brands.
GE Dryer Repair Near Brigham City
Our data shows 19 appliance repair companies inside a 30-mile radius of Brigham City. 1 list an address in Brigham City, and other nearby bases include Ogden (3), Smithfield (3), and Clearfield (3). The farthest listed company is about 29 miles out. None of the companies within 30 miles mention GE by name, so we include matching companies from a longer drive plus the nearest appliance repair companies. Nearest on the list: Murphy's Appliance Sales & Services, around 1.6 miles out. The 15 rated companies in range average 4.5 stars.
We do not show business phone numbers. Call our helpline to be connected with a participating technician, or look a company up directly. Always confirm licensing and insurance.
| Mention GE | 0 |
|---|---|
| Open on Saturdays (per listing) | 11 |
| Appliance repair companies in range (30 mi) | 19 |
| Rated 4.5 stars or higher (10+ reviews) | 10 |
| Distance to the three closest (mi) | 1.6, 13.2, 14.1 |
| List dryer or washer & dryer work | 1 |
At the top of the Brigham City list: General Electric Appliance (52.3 miles away, based in Salt Lake City, 2.8 stars from 4 reviews, lists Saturday hours); Cache Appliance (19.8 miles away, based in Logan, 5.0 stars from 560 reviews); R.A.C.E.R. Service Appliance Repair (16.1 miles away, based in Nibley, 4.7 stars from 12 reviews); Ben Lomond Appliance Repair llc (13.2 miles away, based in North Ogden, 5.0 stars from 155 reviews, lists Saturday hours).
GE Dryer Lines and Features
What a GE Dryer Technician Deals With
The GE Profile UltraFast Combo uses a two-stage filter system (a mesh lint filter plus a second mesh or foam filter) located between the display and the dispenser drawers. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
GE Dryer Symptoms and First Checks
- Electric dryer runs but does not heat. GE says to confirm the dryer has a dedicated 240V supply, reset the breaker fully off and on, and then inspect the power cord and terminal block for burned or loose connections. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
- Dryer takes too long to dry. GE points first to venting (metal duct, no kinks, clear wall cap) and a clean lint filter, then to load size, dryer level and washer spin speed. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
GE Dryer Error Codes
| Code | What it means |
|---|---|
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
GE Dryer Problems Worth a Service Call
- Squealing, thumping or grinding while it runs
- Dryer will not start when you press Start
- Outside of the cabinet gets unusually hot
How a Dryer Service Call Usually Goes in Brigham City
Owner Care for GE Dryers
- Clean the lint filter before every load and periodically wash it in warm soapy water to remove fabric softener film. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
Brand guides: GE Dryer Not Heating: What to Check.
GE Dryer Repair Cost Ranges
Most GE dryer repairs involve common parts and an hour or so of labor. For reference, published cost guides report:
- Drum belt replacement: $150–$250 Source: Fixr - How much does it cost to repair a dryer?
- Control board (part only): $90–$280 Source: Angi - How Much Does Dryer Repair Cost?
- Drum bearing replacement: $100–$250 Source: Fixr - How much does it cost to repair a dryer?
- Dryer not heating (repair by symptom): $80–$420 Source: Angi - How Much Does Dryer Repair Cost?
- Technician labor: $50–$100 per hour Source: Angi - How Much Does Dryer Repair Cost?
A dryer that keeps needing repairs despite regular maintenance is usually cheaper to replace. Source: Angi - How Much Does Dryer Repair Cost?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
What to Have Ready for a GE Dryer Call
- What happens when you press Start (no response, hum, runs with no heat, stops early)
- The brand, model and serial number from the label inside the door or on the back panel
- Whether the dryer is gas or electric
What Brigham City Owners Should Know
Most dryer calls in Brigham City come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Utah has no contractor classification for appliance repair, but under the Construction Trades Licensing Act anyone who installs, repairs or replaces a residential or commercial gas appliance must hold natural gas technician certification, even on jobs otherwise too small to need a contractor license. Source: Utah Legislature H.B. 49 (2004), Natural Gas Technician Certification, amending Utah Code 58-55-305 and 58-55-308
Gas appliance and combustion system work, starting at the outlet of the gas meter, falls under DOPL's construction trades licensing, and the qualifier for an HVAC contractor license must be a Certified Natural Gas Technician. Source: DOPL Contractor Classifications
Hiring a Dryer Repair Company in Brigham City
- If a part has to be ordered, how soon can you come back to finish?
- How often do you repair GE dryers, and do you carry common parts on the truck?
- Can you look at the washer on the same visit if it is acting up too?
GE Dryer Repair FAQs: Brigham City, UT
How do I find a technician who knows GE dryers?
Why does my GE dryer show an error code?
Do you work for GE?
Other Dryer Repair in Brigham City
GE Dryer Repair in Nearby Cities
Before you call, find the model and serial number on your GE dryer's label, usually inside the door opening. A technician who knows the model can often tell you on the phone what the first visit will involve.