A GE dryer shares most of its parts with other dryers, but its controls, error codes and sensor-dry cycles are specific to the brand. Below are independent repair companies serving Independence, with those that mention GE first, then the nearest dryer repair companies.
Independent listings only: Washer and Dryer Repair is not affiliated with or endorsed by GE. If your dryer is still under manufacturer coverage, contact GE directly.
Independent GE Dryer Technicians, Independence IA
We found 40 appliance repair companies within 60 miles of Independence. 1 of them are based in Independence itself, and other nearby bases include Cedar Rapids (18), Waterloo (4), and Marion (4). 1 of them mentions GE in their listing or website. Appliance Plus is the nearest, roughly 0.7 miles from Independence. Across 39 rated companies, the average public rating is 4.7 stars. Because the nearest shops are farther out, ask each company whether Independence is inside its regular service area.
Listings come from public business data. A brand or service mention means the company names it in its listing or website; it is not a certification. Verify experience, licensing and insurance before hiring.
| Open on Saturdays (per listing) | 33 |
|---|---|
| Mention GE | 1 |
| Repair companies inside 60 miles | 46 |
| List dryer or washer & dryer work | 10 |
| Rated 4.5 stars or higher (10+ reviews) | 13 |
| Three nearest companies, miles away | 0.7, 13.1, 14.7 |
Closest matches for Independence: Appliance Plus (0.7 miles away, 5.0 stars from 82 reviews, lists Saturday hours); Sears Appliance Repair (13.1 miles away, based in Oelwein, 4.8 stars from 4 reviews, lists Saturday hours); Sears Appliance Repair (33.3 miles away, based in Cedar Rapids, 4.7 stars from 135 reviews, lists Saturday hours); Sears Appliance Repair (21.4 miles away, based in Waterloo, 4.7 stars from 86 reviews, lists Saturday hours).
Know Your GE Dryer
What a GE Dryer Technician Deals With
An electric GE dryer receiving only partial (120V) power from its 240V circuit can tumble normally but produce no heat, and a dryer wired to a 120V circuit can take up to three times longer to dry. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
The GE Profile UltraFast Combo uses a two-stage filter system (a mesh lint filter plus a second mesh or foam filter) located between the display and the dispenser drawers. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
What GE Says to Check First
- Dryer hot to the touch or sweating. GE says this usually means heat and humidity cannot escape, so clean the exhaust duct, clear the wall cap and confirm the elbow count suits the vent length. Source: GE Appliances - Dryer - Hot to the Touch or Sweats
- Dryer will not run or start. GE's first check is that the dryer plug is pushed fully into the wall outlet. Source: GE Appliances - Dryer - Will Not Run or Start
What GE Dryer Codes Mean
| Code | What it means |
|---|---|
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
When to Call for GE Dryer Repair
- Drum turns but the air stays cool
- Clothes still damp after a full cycle
- Dryer shuts off a few minutes into the cycle
Inside a Dryer Repair Visit
Care GE Recommends for Its Dryers
- Inspect and clean the exhaust duct at least once a year by unplugging the dryer, disconnecting the duct and vacuuming it, and check that the outside hood flaps move freely with no nests inside. Source: GE Appliances - Dryer - How to Clean Exhaust / Vent Duct
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
Brand guides: GE Dryer Not Heating: What to Check.
GE Dryer Repair Cost Ranges
A GE dryer repair usually costs about the same as any other brand for the same part. Published ranges:
- Igniter replacement (gas dryer): $100–$250 Source: Fixr - How much does it cost to repair a dryer?
- Gas valve coil replacement (gas dryer): $150–$300 Source: Fixr - How much does it cost to repair a dryer?
- Drum belt replacement: $150–$250 Source: Fixr - How much does it cost to repair a dryer?
- Drive motor replacement: $250–$450 Source: Fixr - How much does it cost to repair a dryer?
- Typical dryer repair (most homeowners): $100–$430 Source: Angi - How Much Does Dryer Repair Cost?
- Technician labor: $50–$100 per hour Source: Angi - How Much Does Dryer Repair Cost?
If a repair would cost more than about half the price of a new dryer, replacing is usually the better choice. Source: Angi - How Much Does It Cost to Repair a Dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Before the Technician Arrives
- Whether the dryer is gas or electric
- What happens when you press Start (no response, hum, runs with no heat, stops early)
- Any error code on the display
Around Independence
Most dryer calls in Independence come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Iowa does not issue a general appliance repair technician license; the Plumbing and Mechanical Systems Board licenses plumbing, HVAC, refrigeration and hydronic work, and state law carves out a special restricted license only for utility employees who repair appliances. Source: Iowa Code Chapter 105, Plumbers, Mechanical Professionals, and Contractors
Fuel gas piping falls within Iowa's statutory definition of plumbing, and gas lines tied to HVAC, hydronic and refrigeration systems are covered by those mechanical licenses, all issued by the state Plumbing and Mechanical Systems Board; people qualified under liquefied petroleum gas rules may work on propane equipment and its piping. Source: Iowa Code Chapter 105, Plumbers, Mechanical Professionals, and Contractors
Hiring a Dryer Repair Company in Independence
- Is your company licensed where my state requires it, and insured?
- Do you work on gas dryers, and who handles anything involving the gas line?
- If a part has to be ordered, how soon can you come back to finish?
GE Dryer Repair FAQs: Independence, IA
Which Independence technicians work on GE?
Why does my dryer take so long to dry?
Is my GE dryer worth repairing?
Why does my GE dryer show an error code?
Other Dryer Repair in Independence
More GE Dryer Repair Pages Nearby
Before you call, find the model and serial number on your GE dryer's label, usually inside the door opening. A technician who knows the model can often tell you on the phone what the first visit will involve.