Most GE dryer repairs in Fergus Falls involve the same few systems: heat, airflow, the drum drive and the controls. We flag companies whose listing or website mentions GE and fill in with nearby dryer repair companies so you always have options.
Independent listings only: Washer and Dryer Repair is not affiliated with or endorsed by GE. If your dryer is still under manufacturer coverage, contact GE directly.
GE Dryer Repair Near Fergus Falls
12 repair companies serve Fergus Falls from within 60 miles. The rest are spread across Fargo (5), Alexandria (2), and Moorhead (2). The farthest listed company is about 57 miles out. 1 of them mentions GE in their listing or website. The closest is Sears Appliance Repair, about 25.6 miles away. Rated companies nearby average 4.4 stars across 12 businesses. Fergus Falls is a smaller market, so expect a longer drive and ask whether a trip charge applies.
We do not show business phone numbers. Call our helpline to be connected with a participating technician, or look a company up directly. Always confirm licensing and insurance.
| Companies within 60 miles | 12 |
|---|---|
| Listing Saturday hours | 6 |
| List dryer or washer & dryer work | 3 |
| Mention GE | 1 |
| Distance to the three closest (mi) | 25.6, 31.0, 38.3 |
| With 4.5+ stars and at least 10 reviews | 7 |
At the top of the Fergus Falls list: Sears Appliance Repair (25.6 miles away, based in Wahpeton, 4.2 stars from 19 reviews, lists Saturday hours); Sears Appliance Repair (44.3 miles away, based in Alexandria, 4.6 stars from 19 reviews, lists Saturday hours); D & D Appliance, Inc. (38.3 miles away, based in Detroit Lakes, 4.9 stars from 34 reviews); The Appliance Guy FM (50.3 miles away, based in Moorhead, 5.0 stars from 38 reviews, lists Saturday hours).
GE Dryer Features Technicians Work On
How GE Dryers Are Built
An electric GE dryer receiving only partial (120V) power from its 240V circuit can tumble normally but produce no heat, and a dryer wired to a 120V circuit can take up to three times longer to dry. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
Sensor dry models must sit level so tumbling clothes contact the moisture sensors; an unlevel dryer can end cycles with clothes still damp. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
What GE Says to Check First
- Gas dryer runs but does not heat. GE says to confirm a real drying cycle and temperature are selected, keep the front of the dryer unblocked, check the dedicated 120V outlet, and on new installs make sure the gas line is turned on. Source: GE Appliances - Gas Dryer - Runs But Does Not Heat
- Check Vent alert. GE says to unplug the dryer, disconnect and vacuum the duct, and make sure the outside hood damper moves freely. Source: GE Appliances - Dryer - Check Vent Sensor Alert
GE Dryer Error Codes
| Code | What it means |
|---|---|
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
When to Call for GE Dryer Repair
- Outside of the cabinet gets unusually hot
- Dryer will not start when you press Start
- Cycles take two or three runs to finish
What Gets Fixed on a Fergus Falls Dryer Call
Keeping a GE Dryer Running
- Clean the lint filter before every load and periodically wash it in warm soapy water to remove fabric softener film. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
Brand guides: GE Dryer Not Heating: What to Check.
What GE Dryer Repairs Cost
Price the repair before replacing a GE dryer. Published ranges for common jobs:
- Gas valve coil replacement (gas dryer): $150–$300 Source: Fixr - How much does it cost to repair a dryer?
- Thermostat replacement: $100–$260 Source: Fixr - How much does it cost to repair a dryer?
- Control board (part only): $90–$280 Source: Angi - How Much Does Dryer Repair Cost?
- Drum roller replacement: $100–$150 Source: Fixr - How much does it cost to repair a dryer?
- Dryer not heating (repair by symptom): $80–$420 Source: Angi - How Much Does Dryer Repair Cost?
- Technician service / diagnostic fee, dryer: $50–$80 per visit Source: Fixr - How much does it cost to repair a dryer?
A dryer that keeps needing repairs despite regular maintenance is usually cheaper to replace. Source: Angi - How Much Does Dryer Repair Cost?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
What to Have Ready for a GE Dryer Call
- Whether the dryer is gas or electric
- How long the vent run is and where it exits the house
- The brand, model and serial number from the label inside the door or on the back panel
Around Fergus Falls
Most dryer calls in Fergus Falls come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Minnesota has no state license for mechanical contractors or their workers; businesses contracting for gas, heating, cooling or refrigeration work file a mechanical contractor bond with the Department of Labor and Industry, and some cities require their own licenses or competency cards. Source: DLI: Mechanical contractor bond requirements
The state does not license gas fitters; contractors doing gas work must be bonded with the Department of Labor and Industry, and cities such as Minneapolis and St. Paul set their own gas fitter licensing. Source: DLI: Mechanical contractor bond requirements
Questions to Ask a Fergus Falls Technician
- Is your company licensed where my state requires it, and insured?
- How often do you repair GE dryers, and do you carry common parts on the truck?
- What is the service call or diagnostic fee, and is it applied to the repair?
GE Dryer Repair FAQs: Fergus Falls, MN
Why does my GE dryer show an error code?
Why is my dryer running but not heating?
Is this GE customer service?
Related Repair Pages for Fergus Falls
GE Dryer Repair in Nearby Cities
Write down any error code your GE dryer shows and when it appears. It helps a Fergus Falls technician bring the right parts.